The use of living, alkyllithium-initiated anionic polymerization to prepare chain-end functionalized polymers and heteroarm, star-branched polymers is discussed. The scope and limitations of specific termination reactions with a variety of electrophilic species are illustrated for carbonation, hydroxyethylation, amination, and sulfonation. The methodology of using substituted 1,1-diphenylethylenes to provide a general, quantitative functionalization procedure is outlined and illustrated with examples of amine and phenol end-functionalization.A methodology is described for the synthesis of functionalized,star-branched copolymers with compositionally heterogeneous arms of controlled weight and narrow molecular weight distribution using 1,3-bis(1-phenylethenyl)benzene.

The effects of magnetic field on the graft ratio and stereoregularity of grafts of PVA-g-MMA in the presence ofbenzophenone during UV irradiation are discussed. By means of IR, it was found that the graft ratio was increased with the increment of magnetic field strength. Furthermore, application of relative weak magnetic field of 0.4 Tesla had been shown to substantially enhance the stereo-regularity of graft copolymer. The maximum stereo-regularity appeared when the graft ratio approached to 85% with the magnetic field of 1.2 Tesla(T).The resistance to moisture and heat resistance of the grafted copolymer in the presence of magnetic field were also improved.

This study is concerned with chitosan-polyacrylic acid complex as a carrier to immobilize glucose oxidase (GOD)and cellulase. The optimum emperature of the immobilized GOD (IG) was determined to be 60℃ which is higher than that of the native GOD about 40℃. The optimum temperature of the immobilized cellulase (IC) was determined to be about 30℃ higher than that of native cellulase. Both of the optimum pH of IG and IC shifted one pH unit to acid. Immobilized enzyme may be used in more wide pH range. Their storage life are much longer compared with their native states.Both of them can be reused at least 12 times.

The reaction mechanisms of diene polymerization with homogeneous rare earth catalyst are studied by means of the spectra of1H-NMR, one-and two-dimensions 13C-NMR. Based on the data of above NMR spectra, it is proposed that the polymerization reaction proceeds according to the following mechanism: η4-diene (cis-trans-)and η3-allyl (syn-anti-).

Poly (β-carboxyethylmethylsiloxane)-LiClO4 and poly (β-alkoxylethylmethylsiloxane)-LiClO4 crosslinked fllms have been prepared. The ionic conductivity of the films depends on the polymer species, concentration of lithium perchlorate, temperature and content of crosslinking agent. The effect of high polar organic solvent 1, 4-butyrolactone on the ionic conductivity and mechanical properties of poly (β-carhoxyethylmethylsiloxane )-LiClO4 system was also investignied.

A new type of β-diketone based side chain liquid crystalline polysiloxanes (DKLCP) with different length of flexible spacers and end groups have been synthesized by hydrosilation reaction. This is liquid crystal polymers (LCP) using coordinating β-diketone ligand as mesogens. The phase behaviour of DKLCP polymers was studied by differential scanning calorimetry and polarizing microscopy. X-ray diffraction investigations demonstrated that the polysiloxanes with sufficiently long flexible spacers were smectic liquid crystal polymers,while those with much shorter spacers were nematic ones.

A kinetic equation of non-isothermal crystamzation was derived by extending Avrami's equation to the non-isothermal situation. More crystallization information can be obtained from this kinetic equation. The curves of non-isothermal and isothermal crystallizations were analysed and compared for poly (ethylene terephthalate) (PET), and the results were discussed.

In order to improve the mechanical properties of polypyrrole, composites were made by electropolymerizing polypyrrole in a polyurethane matrix. Polypyrrole/polyurethane (PPY/PU) composite films containing CLO4-, BF4-or CH3-C6H4-SO3- counter ions were made in a variety of solvent systems and characterized by SEM, electronic conductivity, FTIR, and mechanical properties. Composite films showing much greater fiexibility than pure polypyrrole were obtained, but their electronic conductivities were substantially lower.Measured conductivities ranged from 0.001 to 8 S/cm, tensile strengths from 44 to 592 psi,and elongation to failure from 3 to 70%.

A series of polymer-supported tetranuclear rhodium carbonyl cluster catalysts were prepared b the reaction of Rh4(CO)12 with several kinds of polymer supports such as crosslinked poly (N-vinylpyrrolidone) (PNVP) and crosslinked poly ( styrene-co-maleic anhydride) (PMAn), and subsequently were used to catalyze the hydroformylation of olefins. The catalysts were characterized by IR, SEM and XPS. The influence of the supports structure and crosslinking, metal's content and particle size of the supports on the catalysts hydroformylation properties was studied.The factors which affect the catalytic convesion were also examined.The experimental results show that the polymer supported Rh cluster catalysts possess very high catalytic activity and aldehyde selectivity as well as good reproducibility.

Surface modification of nucle-microporous membrane by plasma polymerization of HEMA, NVP and D4 has been studied. The hydrophilicity of membranes was increased with increasing of plasma polymerization time of hydrophilic monomers HEMA and NVP. The flow rate of water through the membrane was increased remarkably after plasma polymerization of HEMA on it.

The initiation mechanism of the copolymerization of 2-vinylnaphthalene with maleic anhydride was studied under irradiation of 365 nm. The excited complex was formed from (1) the local excitation of 2-vinylnaphthalene followed by the charge-transfer interaction with maleic anhydride and (2) the excitation of the ground state charge-transfer complex, and then it collapsed to 1,4-tetramethylene biradical for initiation. A1: 1 alternating copolymer was formed in different monomer feeds. Addition of benzophenone could greatly enhance the rate of copolymerization through energy-transfer mechanism.

The polymerization kinetics of 4, 4′-biphenyldicarbonitrile using cuprous chloride-zinc system as catatyst was investigated. the concentration of unreacted cyano group was measured by infrared spectroscopic analysis using potassium ferricyanide as the internal reference. It was found that the polymerization rate is directly proportional to the concentrations ofcyano group, cuprous chloride and zinc, and the activation energy of the polymerization is as Tow as 18.4 KJ/mol. In addition, the other kinetics parameters were obtained and discussed.

Epoxy resins toughened with carboxyl-terminated butadieneacrylonitrile copolymers (CTBN) are two-phase thermosets. The network of the in situ formed rubber particles depends upon the curing mechanism of the resin. When a primary polyamine such as triethylene tetramine was used as curing agent, the network of the rubber phase was quite incomplete, whereas a perfect rubber network was formed with 2-ethyl-4-methyl imidazole as the curing agent.

The polymerization of methyl methacrylate (MMA) initiated by organic peroxide and polymerizable aromatic tertiary amine such as N, N-di (2-α-methylacryloyloxy propyl)-p-toluidine (MP)2PT binary system has been studied. It was found that the (MP)2PT promotes MMA polymerization, and the kinetics of MMA polymerization fits the radical polymerization rate equation. Based on the ESR studies and the end-group analysis the initiation mechanism is proposed.