General Model of Temperature-dependent Modulus and Yield Strength of Thermoplastic Polymers

Ping-Yuan Huang; Zhan-Sheng Guo; Jie-Min Feng

doi:10.1007/s10118-020-2360-7

Your Location：

Home >

Browse articles >

General Model of Temperature-dependent Modulus and Yield Strength of Thermoplastic Polymers

ARTICLE | Updated：2019-12-06

- General Model of Temperature-dependent Modulus and Yield Strength of Thermoplastic Polymers
- Chinese Journal of Polymer Science Vol. 38, Issue 4, Pages: 382-393(2020)
- Affiliations：
  
  a.Shanghai Institute of Applied Mathematics and Mechanics, School of Mechanics and Engineering Science, Shanghai University, Shanghai 200072, China
  b.Shanghai Key Laboratory of Mechanics in Energy Engineering, Shanghai 200072, China
- Author bio：
  
  fengjiemin@shu.edu.cn
- Funds：
- DOI：10.1007/s10118-020-2360-7
  CLC：
- Received：14 July 2019，
  
  Revised：2019-9-7，
  
  Accepted：30 September 2019，
  
  Online First：06 December 2019，
  
  Published：2020-04
- Accepted：
Scan QR Code
Huang, P. Y.; Guo, Z. S.; Feng, J. M. General model of temperature-dependent modulus and yield strength of thermoplastic polymers. Chinese J. Polym. Sci. 2020, 38, 382–393

Ping-Yuan Huang, Zhan-Sheng Guo, Jie-Min Feng. General Model of Temperature-dependent Modulus and Yield Strength of Thermoplastic Polymers[J]. Chinese Journal of Polymer Science, 2020, 38(4): 382-393.
Huang, P. Y.; Guo, Z. S.; Feng, J. M. General model of temperature-dependent modulus and yield strength of thermoplastic polymers. Chinese J. Polym. Sci. 2020, 38, 382–393 DOI： 10.1007/s10118-020-2360-7.

Ping-Yuan Huang, Zhan-Sheng Guo, Jie-Min Feng. General Model of Temperature-dependent Modulus and Yield Strength of Thermoplastic Polymers[J]. Chinese Journal of Polymer Science, 2020, 38(4): 382-393. DOI： 10.1007/s10118-020-2360-7.

摘要

Abstract

A general model was developed to predict the temperature-dependent modulus and yield strength of different thermoplastic polymers. This model

which depends on only two parameters with clear and specific physical meanings

can describe the temperature-dependent modulus and yield strength of thermoplastic polymers over the full glass transition region. The temperature-dependent modulus and yield strength of three thermoplastic polymers were measured by uniaxial tension tests over a temperature range of 243−383 K. The predictions showed excellent agreement with the experimental data. Sensitivity analysis of model input parameters showed negligible effect on the present general model. The universality of the present general model was further validated

showing excellent agreement with published experimental data on other thermoplastic polymers and their composites.

关键词

Keywords

references

Dubary, N.; Taconet, G.; Bouvet, C.; Vieille, B . Influence of temperature on the impact behavior and damage tolerance of hybrid woven-ply thermoplastic laminates for aeronautical applications . Compos. Struct. , 2017 . 168 663 - 674 . DOI: 10.1016/j.compstruct.2017.02.040 http://doi.org/10.1016/j.compstruct.2017.02.040 .

Malpot, A.; Touchard, F.; Bergamo, S . Influence of moisture on the fatigue behaviour of a woven thermoplastic composite used for automotive application . Mater. Des. , 2016 . 98 12 - 19 . .

Kalnaus, S.; Wang, Y.; Turner, J. A . Mechanical behavior and failure mechanisms of Li-ion battery separators . J. Power Sources , 2017 . 348 255 - 263 . DOI: 10.1016/j.jpowsour.2017.03.003 http://doi.org/10.1016/j.jpowsour.2017.03.003 .

Ching, Y. C.; Chuah, C. H.; Ching, K. Y.; Abdullah, L. C.; Rahman, A. In Recent developments in polymer macro, micro and nano blends. Vol. 5, ed. By Visakh, P. M.; Markovic, G.; Pasquini, D. Woodhead Publishing, Oxford, 2017 , p. 111−129.

Sperling, L. H. In Introduction to physical polymer science , 4 th edn. Vol. 1, ed. By Sperling, L. H. John. Wiley. & amp;. Sons, Inc, 2005 , p. 1−28.

Gu, P.; Asaro, R. J . Structural buckling of polymer matrix composites due to reduced stiffness from fire damage . Compos. Struct. , 2005 . 69 65 - 75 . DOI: 10.1016/j.compstruct.2004.05.016 http://doi.org/10.1016/j.compstruct.2004.05.016 .

Ha, S. K.; Springer, G. S . Nonlinear mechanical properties of a thermoset matrix composite at elevated temperatures . J. Compos. Mater. , 1989 . 23 1130 - 1158 . DOI: 10.1177/002199838902301103 http://doi.org/10.1177/002199838902301103 .

Dutta, P. K.; Hui, D . Creep rupture of a GFRP composite at elevated temperatures . Compu. Struct. , 2000 . 76 153 - 161 . DOI: 10.1016/S0045-7949(99)00176-5 http://doi.org/10.1016/S0045-7949(99)00176-5 .

Wang, S.; Zhou, Z.; Zhang, J.; Fang, G.; Wang, Y . Effect of temperature on bending behavior of woven fabric-reinforced PPS-based composites . J. Mater. Sci. , 2017 . 52 13966 - 13976 . DOI: 10.1007/s10853-017-1480-0 http://doi.org/10.1007/s10853-017-1480-0 .

Murayama, T.; Bell, J. P . Relation between the network structure and dynamic mechanical properties of a typical amine-cured epoxy polymer . J. Polym. Sci., Part B: Polym. Phys. , 1970 . 8 437 - 445 . DOI: 10.1002/pol.1970.160080309 http://doi.org/10.1002/pol.1970.160080309 .

Mahieux, C. A.; Reifsnider, K. L . Property modeling across transition temperatures in polymers: a robust stiffness-temperature model . Polymer , 2001 . 42 3281 - 3291 . DOI: 10.1016/S0032-3861(00)00614-5 http://doi.org/10.1016/S0032-3861(00)00614-5 .

Mahieux, C. A.; Reifsnider, K. L . Property modeling across transition temperatures in polymers: application to thermoplastic systems . J. Mater. Sci. , 2002 . 37 911 - 920 . DOI: 10.1023/A:1014383427444 http://doi.org/10.1023/A:1014383427444 .

Gibson, A. G.; Browne, T. N. A.; Feih, S.; Mouritz, A. P . Modeling composite high temperature behavior and fire response under load . J. Compos. Mater. , 2012 . 46 2005 - 2022 . DOI: 10.1177/0021998311429383 http://doi.org/10.1177/0021998311429383 .

Gibson, A. G.; Wu, Y. S.; Evans, J. T.; Mouritz, A. P . Laminate theory analysis of composites under load in fire . J. Compos. Mater. , 2006 . 40 639 - 658 . DOI: 10.1177/0021998305055543 http://doi.org/10.1177/0021998305055543 .

Bai, Y.; Keller, T.; Vallee, T . Modeling of stiffness of FRP composites under elevated and high temperatures . Compos. Sci. Technol. , 2008 . 68 3099 - 3106 . DOI: 10.1016/j.compscitech.2008.07.005 http://doi.org/10.1016/j.compscitech.2008.07.005 .

Guo, Z. S.; Feng, J. M.; Wang, H.; Hu, H. J.; Zhang, J. Q . A new temperature-dependent modulus model of glass/epoxy composite at elevated temperatures . J. Compos. Mater. , 2013 . 47 3303 - 3310 . DOI: 10.1177/0021998312464080 http://doi.org/10.1177/0021998312464080 .

Feng, J. M.; Guo, Z. S . Temperature-frequency-dependent mechanical properties model of epoxy resin and its composites . Compos. Part B-Eng. , 2016 . 85 161 - 169 . DOI: 10.1016/j.compositesb.2015.09.040 http://doi.org/10.1016/j.compositesb.2015.09.040 .

Feng, J. M.; Guo, Z. S . Effects of temperature and frequency on dynamic mechanical properties of glass/epoxy composites . J. Mater. Sci. , 2016 . 51 2747 - 2758 . DOI: 10.1007/s10853-015-9589-5 http://doi.org/10.1007/s10853-015-9589-5 .

Eyring, H . Viscosity, plasticity and diffusion as examples of absolute reaction rates . J. Chem. Phys. , 1936 . 4 283 - 291 . DOI: 10.1063/1.1749836 http://doi.org/10.1063/1.1749836 .

Halsey, G.; White, H. J.; Eyring, H . Mechanical properties of textiles I . Text. Res. , 1945 . 15 295 - 311 . DOI: 10.1177/004051754501500901 http://doi.org/10.1177/004051754501500901 .

Ree, T.; Eyring, H . Theory of non-Newtonian flow. I. Solid plastic system . J. Appl. Phys. , 1955 . 26 793 - 800 . DOI: 10.1063/1.1722098 http://doi.org/10.1063/1.1722098 .

Govaert, L. E.; Vries, P. J.; Fennis, P. J.; Nijenhuis, W. F.; Keustermans, J. P . Influence of strain rate, temperature and humidity on the tensile yield behaviour of aliphatic polyketone . Polymer , 2000 . 41 1959 - 1962 . DOI: 10.1016/S0032-3861(99)00468-1 http://doi.org/10.1016/S0032-3861(99)00468-1 .

Chaleat, C. M.; Michel-Amadry, G.; Halley, P. J.; Truss, R. W . Properties of a plasticised starch blend—Part 2: influence of strain rate, temperature and moisture on the tensile yield behaviour . Carbohydr. Polym. , 2008 . 74 366 - 371 . DOI: 10.1016/j.carbpol.2008.03.002 http://doi.org/10.1016/j.carbpol.2008.03.002 .

Lim, S. H.; Yu, Z. Z.; Mai, Y. W . Effects of loading rate and temperature on tensile yielding and deformation mechanisms of nylon 6-based nanocomposites . Compos. Sci. Technol. , 2010 . 70 1994 - 2002 . DOI: 10.1016/j.compscitech.2010.07.023 http://doi.org/10.1016/j.compscitech.2010.07.023 .

Kambour, R. P . A review of crazing and fracture in thermoplastics . J. Polym. Sci. Macromol. Rev. , 1973 . 7 1 - 154 . .

Le Gac, P. Y.; Arhant, M.; Gall, M. L.; Davies, P . Yield stress changes induced by water in polyamide 6: characterization and modeling . Polym. Degrad. Stab. , 2017 . 137 272 - 280 . DOI: 10.1016/j.polymdegradstab.2017.02.003 http://doi.org/10.1016/j.polymdegradstab.2017.02.003 .

Bai, Y.; Keller, T . Time dependence of material properties of FRP composites in fire . J. Compos. Mater. , 2009 . 43 2469 - 2484 . DOI: 10.1177/0021998309344641 http://doi.org/10.1177/0021998309344641 .

Bai, Y.; Keller, T . Pultruded GFRP tubes with liquid-cooling system under combined temperature and compressive loading . Compos. Struct. , 2009 . 90 115 - 121 . DOI: 10.1016/j.compstruct.2009.02.009 http://doi.org/10.1016/j.compstruct.2009.02.009 .

Bai, Y.; Keller, T . Modeling of mechanical response of FRP composites in fire . Compos. Part A-Appl. Sci. Manuf. , 2009 . 40 731 - 738 . DOI: 10.1016/j.compositesa.2009.03.003 http://doi.org/10.1016/j.compositesa.2009.03.003 .

Bai, Y.; Keller, T.; Correia, J. R.; Branco, F. A.; Ferreira, J. G . Fire protection systems for building floors made of pultruded GFRP profiles—Part 2: modeling of thermomechanical responses . Compos. Part B-Eng. , 2010 . 41 630 - 636 . DOI: 10.1016/j.compositesb.2010.09.019 http://doi.org/10.1016/j.compositesb.2010.09.019 .

Correia, J. R.; Gomes, M. M.; Pires, J. M.; Branco, F. A . Mechanical behaviour of pultruded glass fibre reinforced polymer composites at elevated temperature: experiments and model assessment . Compos. Struct. , 2013 . 98 303 - 313 . DOI: 10.1016/j.compstruct.2012.10.051 http://doi.org/10.1016/j.compstruct.2012.10.051 .

Feng, P.; Wang, J.; Tian, Y.; Loughery, D.; Wang, Y . Mechanical behavior and design of FRP structural members at high and low service temperatures . J. Compos. Constr. , 2016 . 20 04016021 DOI: 10.1061/(ASCE)CC.1943-5614.0000676 http://doi.org/10.1061/(ASCE)CC.1943-5614.0000676 .

Wu, C.; Bai, Y.; Mottram, J. T . Effect of elevated temperatures on the mechanical performance of pultruded FRP joints with a single ordinary or blind bolt . J. Compos. Constr. , 2016 . 20 04015045 DOI: 10.1061/(ASCE)CC.1943-5614.0000608 http://doi.org/10.1061/(ASCE)CC.1943-5614.0000608 .

Fang, H.; Wong, M. B.; Bai, Y . Heating rate effect on the thermophysical properties of steel in fire . J. Constr. Steel. Res. , 2017 . 128 611 - 617 . DOI: 10.1016/j.jcsr.2016.09.016 http://doi.org/10.1016/j.jcsr.2016.09.016 .

Rosa, I. C.; Morgado, T.; Correia, J. R.; Firmo, J. P.; Silvestre, N . Shear behavior of GFRP composite materials at elevated temperature . J. Compos. Constr. , 2018 . 22 04018010 DOI: 10.1061/(ASCE)CC.1943-5614.0000839 http://doi.org/10.1061/(ASCE)CC.1943-5614.0000839 .

Zhang, L.; Bai, Y.; Qi, Y. J.; Fang, H.; Wu, B. S . Post-fire mechanical performance of modular GFRP multicellular slabs with prefabricated fire resistant panels . Compos. Part B-Eng. , 2018 . 143 55 - 67 . DOI: 10.1016/j.compositesb.2018.01.034 http://doi.org/10.1016/j.compositesb.2018.01.034 .

Singla, R. K.; Maiti, S. N.; Ghosh, A. K . Mechanical, morphological, and solid-state viscoelastic responses of poly(lactic acid)/ethylene- co -vinyl-acetate super-tough blend reinforced with halloysite nanotubes . J. Mater. Sci. , 2016 . 51 10278 - 10292 . DOI: 10.1007/s10853-016-0255-3 http://doi.org/10.1007/s10853-016-0255-3 .

Banerjee, S. S.; Bhowmick, A. K . An effective strategy to develop nanostructured morphology and enhanced physico-mechanical properties of PP/EPDM thermoplastic elastomers . J. Mater. Sci. , 2016 . 51 6722 - 6734 . DOI: 10.1007/s10853-016-9959-7 http://doi.org/10.1007/s10853-016-9959-7 .

Zhou, R.; Gao, W. Q.; Xia, L. C.; Wu, H.; Guo, S. Y . The study of damping property and mechanism of thermoplastic polyurethane/phenolic resin through a combined experiment and molecular dynamics simulation . J. Mater. Sci. , 2018 . 53 9350 - 9362 . DOI: 10.1007/s10853-018-2218-3 http://doi.org/10.1007/s10853-018-2218-3 .

Richards, F. J . A flexible growth function for empirical use . J. Exp. Bot. , 1959 . 10 290 - 301 . DOI: 10.1093/jxb/10.2.290 http://doi.org/10.1093/jxb/10.2.290 .

Xu, L.; Selin, V.; Zhuk, A.; Ankner, J. F.; Sukhishvili, S. A . Molecular weight dependence of polymer chain mobility within multilayer films . ACS Macro Lett. , 2013 . 2 865 - 868 . DOI: 10.1021/mz400413v http://doi.org/10.1021/mz400413v .

Lin, Y. F.; Li, X. Y.; Meng, L. P.; Chen, X. W.; Lv, F.; Zhang, Q. L.; Zhang, R.; Li, L. B . Structural evolution of hard-elastic isotactic polypropylene film during uniaxial tensile deformation: The effect of temperature . Macromolecules , 2018 . 51 2690 - 2705 . DOI: 10.1021/acs.macromol.8b00255 http://doi.org/10.1021/acs.macromol.8b00255 .

ISO, 527. Plastics determination of tensile properties—Part 2: test conditions for moulding and extrusion plastics. ISO, Genève, 2012 , p. 1−14

Ghorbel, E . A viscoplastic constitutive model for polymeric materials . Int. J. Plast. , 2008 . 24 2032 - 2058 . DOI: 10.1016/j.ijplas.2008.01.003 http://doi.org/10.1016/j.ijplas.2008.01.003 .

Jancar, J.; Hoy, R. S.; Jancarova, E.; Zidek, J . Effect of temperature, strain rate and particle size on the yield stresses and post-yield strain softening of PMMA and its composites . Polymer , 2015 . 63 196 - 207 . DOI: 10.1016/j.polymer.2015.03.001 http://doi.org/10.1016/j.polymer.2015.03.001 .

Cheng, S. W.; Wang, S. Q . Elastic yielding in cold drawn polymer glasses well below the glass transition temperature . Phys. Rev. Lett. , 2013 . 110 1 - 4 . .

Jin, T.; Zhou, Z. W.; Shu, X. F.; Wang, Z. H.; Wu, G. Y.; Zhao, L. M . Investigation on the yield behaviour and macroscopic phenomenological constitutive law of PA66 . Polym. Test. , 2018 . 69 563 - 582 . DOI: 10.1016/j.polymertesting.2018.06.014 http://doi.org/10.1016/j.polymertesting.2018.06.014 .

Jin, T.; Zhou, Z. W.; Shu, X. F.; Wang, Z. H.; Wu, G. Y.; Zhao, L. M . Experimental investigation on the yield loci of PA66 . Polym. Test. , 2016 . 51 148 - 150 . DOI: 10.1016/j.polymertesting.2016.03.007 http://doi.org/10.1016/j.polymertesting.2016.03.007 .

Tang, Y. L.; Karlsson, A. M.; Santare, M. H.; Gilbert, M.; Cleghorn, S.; Johnson, W. B . An experimental investigation of humidity and temperature effects on the mechanical properties of perfluorosulfonic acid membrane . Mater. Sci. Eng. A-Struct. Mater. Prop. Microstruct. Process. , 2006 . 425 297 - 304 . DOI: 10.1016/j.msea.2006.03.055 http://doi.org/10.1016/j.msea.2006.03.055 .

Akay, M . Aspects of dynamic mechanical analysis in polymeric composites . Compos. Sci. Technol. , 1993 . 47 419 - 423 . DOI: 10.1016/0266-3538(93)90010-E http://doi.org/10.1016/0266-3538(93)90010-E .

Künniger, T.; Grüneberger, F.; Fischer, B.; Walder, C . Nanofibrillated cellulose in wood coatings: viscoelastic properties of free composite films . J. Mater. Sci. , 2017 . 52 10237 - 10249 . DOI: 10.1007/s10853-017-1193-4 http://doi.org/10.1007/s10853-017-1193-4 .

Mauro, J. C.; Yue, Y. Z.; Ellison, A. J.; Gupta, P. K.; Allan, D. C . Viscosity of glass-forming liquids . Proc. Natl. Acad. Sci. , 2009 . 106 19780 - 19784 . DOI: 10.1073/pnas.0911705106 http://doi.org/10.1073/pnas.0911705106 .

Williams, M. L.; Landel, R. F.; Ferry, J. D . The temperature dependence of relaxation mechanisms in amorphous polymers and other glass-forming liquids . J. Am. Chem. Soc. , 1955 . 77 3701 - 3707 . DOI: 10.1021/ja01619a008 http://doi.org/10.1021/ja01619a008 .

Xiao, C.; Jho, J. Y.; Yee, A. F . Correlation between the shear yielding behavior and secondary relaxations of bisphenol a polycarbonate and related copolymers . Macromolecules , 1994 . 27 2761 - 2768 . DOI: 10.1021/ma00088a017 http://doi.org/10.1021/ma00088a017 .

Ferrillo, R. G.; Achorn, P. J . Comparison of thermal techniques for glass transition assignment. II. Commercial polymers . J. Appl. Polym. Sci. , 1997 . 64 191 - 195 . .

Monemian, S.; Jafari, S. H.; Khonakdar, H. A . Pötschke, P. Dynamic-mechanical analysis of MWNTs-filled PC/ABS blends . Polym. Eng. Sci. , 2014 . 54 2696 - 2706 . DOI: 10.1002/pen.23834 http://doi.org/10.1002/pen.23834 .

Ma, L.; Zhang, Y.; Meng, Y.; Anusonti-Inthra, P.; Wang, S . Preparing cellulose nanocrystal/acrylonitrile-butadiene-styrene nanocomposites using the master-batch method . Carbohydr. Polym. , 2015 . 125 352 - 359 . DOI: 10.1016/j.carbpol.2015.02.062 http://doi.org/10.1016/j.carbpol.2015.02.062 .

Zhang, S. U.; Han, J.; Kang, H. W . Temperature-dependent mechanical properties of ABS parts fabricated by fused deposition modeling and vapor smoothing . Int. J. Precis. Eng. Manuf. , 2017 . 18 763 - 769 . DOI: 10.1007/s12541-017-0091-7 http://doi.org/10.1007/s12541-017-0091-7 .

Tjong, S. C.; Jiang, W . Mechanical performance of ternary in situ polycarbonate/poly(acrylonitrile-butadiene-styrene)/liquid crystalline polymer composites . J. Appl. Polym. Sci. , 1999 . 74 2274 - 2282 . DOI: 10.1002/(SICI)1097-4628(19991128)74:9<2274::AID-APP17>3.0.CO;2-1 http://doi.org/10.1002/(SICI)1097-4628(19991128)74:9<2274::AID-APP17>3.0.CO;2-1 .

Manchanda, B.; Kottiyath, V. K.; Kapur, G. S.; Kant, S.; Choudhary, V . Morphological studies and thermo-mechanical behavior of polypropylene/sepiolite nanocomposites . Polym. Compos. , 2017 . 38 E285 - E294 . DOI: 10.1002/pc.23800 http://doi.org/10.1002/pc.23800 .

Chafidz, A.; Rengga, W. D. P.; Khan, R.; Kaavessina, M.; Almutlaq, A. M.; Almasry, W. A.; Ajbar, A . Polypropylene/multiwall carbon nanotubes nanocomposites: nanoindentation, dynamic mechanical, and electrical properties . J. Appl. Polym. Sci. , 2017 . 134 45293 DOI: 10.1002/app.45293 http://doi.org/10.1002/app.45293 .

Li, L. B . In situ synchrotron radiation techniques: Watching deformation-induced structural evolutions of polymers . Chinese J. Polym. Sci. , 2018 . 36 1093 - 1102 . DOI: 10.1007/s10118-018-2169-9 http://doi.org/10.1007/s10118-018-2169-9 .

Zhou, C. B.; Guo, H. L.; Li, J. Q.; Huang, S. Y.; Li, H. F.; Meng, Y. F.; Yu, D. H.; Christiansen, J. D.; Jiang, S. C . Temperature dependence of poly(lactic acid) mechanical properties . RSC Adv. , 2016 . 6 113762 - 113772 . DOI: 10.1039/C6RA23610C http://doi.org/10.1039/C6RA23610C .

Zhang, W. Y.; Li, J. Q.; Li, H. F.; Jiang, S. C.; An, L. J . Temperature dependence of deformation behavior of poly(butylene terephthalate) . Polymer , 2018 . 143 309 - 315 . DOI: 10.1016/j.polymer.2018.04.030 http://doi.org/10.1016/j.polymer.2018.04.030 .

Cao, J.; Wen, N.; Zheng, Y. Y . Effect of long chain branching on the rheological behavior, crystallization and mechanical properties of polypropylene random copolymer . Chinese J. Polym. Sci. , 2016 . 34 1158 - 1171 . DOI: 10.1007/s10118-016-1830-4 http://doi.org/10.1007/s10118-016-1830-4 .

Flory, P. J.; Yoon, D. Y . Molecular morphology in semicrystalline polymers . Nature , 1978 . 272 226 - 229 . DOI: 10.1038/272226a0 http://doi.org/10.1038/272226a0 .

Zhu, S. Z.; Lempesis, N.; In't Veld, P. J.; Rutledge, G. C . Molecular simulation of thermoplastic polyurethanes under large tensile deformation . Macromolecules , 2018 . 51 1850 - 1864 . DOI: 10.1021/acs.macromol.7b02367 http://doi.org/10.1021/acs.macromol.7b02367 .

Zhu, S. Z.; Lempesis, N.; In't Veld, P. J.; Rutledge, G. C . Molecular simulation of thermoplastic polyurethanes under large compressive deformation . Macromolecules , 2018 . 51 9306 - 9316 . DOI: 10.1021/acs.macromol.8b01922 http://doi.org/10.1021/acs.macromol.8b01922 .

Views

Downloads

CSCD

Alert me when the article has been cited

Submit

Tools

Publicity Resources

Long Alkyl Tails Amplify Photoswitchable Glass Transition Temperatures of Azopolymers for Nanoimprint Lithography

Rheological Behaviors of Polymers with Nanoparticles Tethered at Each End

Nonlinear Viscoelasticity Raised at Low Temperatures by Intermolecular Cooperation of Bulk Amorphous Polymers

Squaramide-directed Cooperative One-dimensional Assembly in Telechelic Polydimethylsiloxane for Hierarchical Network Formation

pH-Responsive L-Cysteine-conjugated Polydopamine Nanocarriers for Controlled Release of Emamectin Benzoate against Pieris brassicae

Related Author

Si Wu

Shuo-Feng Liang

Tian-Ren Zhao

Bo-Ting Wang

Jie Yan

Jia-Hui Chen

Fu-Wei Kong

Zhu-Lu Xie

Related Institution

Hefei National Research Center for Physical Sciences at the Microscale, Anhui Key Laboratory of Optoelectronic Science and Technology, Department of Polymer Science and Engineering, University of Science and Technology of China

Shanghai Key Laboratory of Advanced Polymeric Materials, Key Laboratory for Ultrafine Materials of Ministry of Education, School of Materials Science and Engineering, East China University of Science and Technology

Department of Polymer Science and Engineering, State Key Lab of Coordination Chemistry, School of Chemistry and Chemical Engineering, Nanjing University

Shanghai Key Laboratory of Advanced Polymeric Materials, School of Materials Science & Engineering, East China University of Science & Technology

Department of Polymeric and Organic Materials Engineering, Graduate School of Organic Materials Science, Yamagata University, 4-3-16 Jonan, Yonezawa

⁰